EN25QH64A 7010B Car MP5 Flash Dump 8MB

User question

en25QH64A اريد فلاش من فضلكم لم اجده 7010b

Artificial Intelligence Response

Direct answer to the question

You are looking for a flash/dump file for EN25QH64A in a 7010B car MP5/radio unit.
The important point is:

Do not program a random 7010B EN25QH64A file.
The label 7010B and the SPI flash chip EN25QH64A / 25QH64 / W25Q64-type, 8 MB are not enough to identify the correct firmware.

You must provide the main board number printed on the PCB and preferably the CPU type. Many 7010B/7018B units use the same 8 MB SPI flash but different boards, LCD panels, touch controllers, audio ICs, and MCU configurations. Using the wrong dump can cause black screen, white screen, inverted touch, no sound, or a completely dead unit. This is confirmed by repair discussions where technicians recommend matching the firmware by exact board/CPU, not only by “7010B”. (elektroda.com)

---

Detailed problem analysis

1. What EN25QH64A is

EN25QH64A is a serial SPI NOR flash memory, usually:

Parameter	Value
Type	SPI NOR Flash
Capacity	64 Mbit
File size expected	8 MB
Common programmer support	CH341A, RT809H, TL866/T48/T56, TNM, etc.
Typical voltage	3.3 V

So if you download the correct dump, the file should normally be around 8 MB. For example, one available 7010B dump for board ZCD7089-C200S-MAIN-V2.0 is listed as a 25QH64 dump, size 8.00 MB. (repairalltv.com)

2. Why “7010B” is not enough

The model name 7010B is generic. It is used by many Chinese manufacturers for similar-looking 2-DIN car MP5 players. Internally, they can be very different.

Possible differences include:

• CPU: for example Allwinner F1C200S, F1C500, C500, or other variants.
• Main board: for example:
  • ZCD7089-C200S-MAIN-V2.0
  • ZCD7106-C200S-MAIN-V2.2
  • DFL-HGJ-FC200S-MP5-MB
  • SK-848-MAIN-V6.1
  • 7018B V1.0
  • 7023B-C500 V01.1
• LCD panel resolution and initialization code.
• Touch panel controller.
• Audio processor.
• Radio tuner IC.
• MCU firmware/configuration.

Remont-Aud and Elektroda listings show multiple different 7010B/no-name boards using similar 25Q64 or XM25QH64A-type flash chips, which demonstrates why the exact PCB version is necessary. (remont-aud.net)

3. What can go wrong with the wrong dump

If the dump does not match your hardware, common symptoms are:

• Unit powers on but shows black screen.
• White screen or colored lines because of wrong LCD driver/init sequence.
• Touch panel does not work or axes are inverted.
• Buttons or steering wheel control do not work.
• No sound because the audio IC configuration is different.
• Boot loop or stuck on logo.
• Device becomes apparently dead.

A recent Elektroda case about a similar unit shows that installing the wrong 7010B update on a different board can brick the radio or cause boot/display failure. (elektroda.com)

---

Practical guidelines

Step 1: Open the unit and find the board number

Remove the cover and look for text printed directly on the PCB. It may be white silkscreen text such as:

• ZCD7089-C200S-MAIN-V2.0
• ZCD7106-C200S-MAIN-V2.2G
• DFL-HGJ-FC200S-MP5-MB
• SK-848-MAIN-V6.1
• SK-848-main-v6.7-6905C
• 7018B V1.0
• 7023B-C500 V01.1

Also read the large CPU marking. Examples:

• F1C200S
• F1C500
• C500
• Quanzhi C500

Step 2: Backup your original flash before writing anything

Before erasing the EN25QH64A:

1. Read the chip with the programmer.
2. Save the file as original_read1.bin.
3. Read again and save as original_read2.bin.
4. Compare both files.
5. Only continue if both reads are identical or nearly identical.

This is very important. Even a corrupted original dump may contain calibration, MCU, touch, panel, or device-specific data that can help recover the unit later. RepairAllTV also advises backing up the original firmware before programming because of possible incompatibility. (repairalltv.com)

Step 3: Use the correct programming method

If the radio does not boot, the safest method is usually:

• Desolder the EN25QH64A or use a high-quality SOIC8 clip.
• Program it using an external SPI programmer.
• Use 3.3 V, not 5 V.
• Erase, blank-check, write, then verify.
• Reinstall the chip in the correct orientation.

If the unit still boots and has a working menu, some versions can be updated by USB/SD using an .img file from the firmware update menu, but a .bin dump is normally written directly to the SPI flash using a programmer. Elektroda discussions distinguish between USB/SD update when the radio still boots and external SPI programming when the firmware is damaged. (elektroda.com)

---

Current information and available dump examples

I found evidence of available dumps, but they are board-specific:

Board / chassis	Flash	Notes
ZCD7089-C200S-MAIN-V2.0	25QH64 / EN25QH64	7010B dump listed, 8 MB file size. (repairalltv.com)
DFL-HGJ-FC200S-MP5-MB	25Q64-type	Mentioned in repair discussions as a separate board requiring its own dump. (elektroda.com)
SK-848-MAIN-V6.1	XM25QH64A	Listed as a no-name 7010B variant. (remont-aud.net)
7018B V1.0	25Q64	Listed as a 7010B/7018B chassis variant. (remont-aud.net)
7023B-C500 V01.1	QH64-type	Listed as another 7010B no-name variant. (remont-aud.net)

So, if your board is ZCD7089-C200S-MAIN-V2.0, there appears to be a matching 7010B 25QH64 8 MB dump available. But if your board is different, that file may not be safe for your device.

---

What I need from you to identify the correct flash

Please send these details:

1. Exact board number printed on the PCB.
2. CPU marking written on the large processor IC.
3. A photo of:
   • main board,
   • flash chip area,
   • CPU area,
   • front panel board if separate.
4. Current fault:
   • dead/no power,
   • stuck on logo,
   • white screen,
   • black screen,
   • touch not working,
   • no sound,
   • boot loop.

With that information, the correct dump can be searched much more accurately.

---

Possible disclaimers or additional notes

Firmware dumps may be copyrighted or vendor-specific. In repair practice, they are usually used as recovery backups for the same hardware version. Avoid distributing or using files unless you have the right to service that device.

Also, automotive electronics should be tested safely:

• Use a current-limited bench power supply.
• Do not test directly in the car immediately after flashing.
• Confirm correct polarity: usually yellow = B+, red = ACC, black = GND, but verify your wiring.

---

Brief summary

You need a flash file for EN25QH64A in a 7010B, but the correct file cannot be selected from “7010B” alone. You must match the exact board number and CPU. The expected dump size is normally 8 MB. Before writing anything, read and save the original flash twice, compare the files, then program only a dump known to match your PCB version.

Disclaimer: The responses provided by artificial intelligence (language model) may be inaccurate and misleading. Elektroda is not responsible for the accuracy, reliability, or completeness of the presented information. All responses should be verified by the user.