PowerWorld transient stability results not generating with simple PSS/E RAW file system

Hi, 

I am Maria. I am working in a project with PowerWorld and I am not able to get  transient stability results. 

I use a simple system, whose raw file is: 
0,   100.00          / PSS/E-33.2    SUN, MAR 10 2013  17:41


     1,'BUS1        ', 345.0000,3,   1,   1,   1,1.04000,  -0.0000,1.10000,0.90000,1.10000,0.90000
     2,'BUS2        ', 345.0000,1,   1,   1,   1,1.01613,  -3.3252,1.10000,0.90000,1.10000,0.90000
0 / END OF BUS DATA, BEGIN LOAD DATA
     2,'11',1,   1,   1,     0.000,     0.000,     0.000,     0.000,   103.130,   -37.617,   1,1,0
0 / END OF LOAD DATA, BEGIN FIXED SHUNT DATA
0 / END OF FIXED SHUNT DATA, BEGIN GENERATOR DATA
     1,'1 ',   106.496,    45.996,   300.000,  -300.000,1.04000,     0,   100.000, 0.00000E+0, 1.73300E-1, 0.00000E+0, 0.00000E+0,1.00000,1,  100.0,   999.000,    10.000,   1,1.0000
0 / END OF GENERATOR DATA, BEGIN BRANCH DATA
     1,     2,'1 ', 1.00000E-4, 5.76000E-2,   0.00010,  250.00,  250.00,  250.00,  0.00000,  0.00000,  0.00000,  0.00000,1,1,   0.00,   1,1.0000
0 / END OF BRANCH DATA, BEGIN TRANSFORMER DATA
0 / END OF TRANSFORMER DATA, BEGIN AREA DATA
   1,     1,     0.000,    10.000,'            '
0 / END OF AREA DATA, BEGIN TWO-TERMINAL DC DATA
0 / END OF TWO-TERMINAL DC DATA, BEGIN VSC DC LINE DATA
0 / END OF VSC DC LINE DATA, BEGIN IMPEDANCE CORRECTION DATA
0 / END OF IMPEDANCE CORRECTION DATA, BEGIN MULTI-TERMINAL DC DATA
0 / END OF MULTI-TERMINAL DC DATA, BEGIN MULTI-SECTION LINE DATA
0 / END OF MULTI-SECTION LINE DATA, BEGIN ZONE DATA
0 / END OF ZONE DATA, BEGIN INTER-AREA TRANSFER DATA
0 / END OF INTER-AREA TRANSFER DATA, BEGIN OWNER DATA
0 / END OF OWNER DATA, BEGIN FACTS DEVICE DATA
0 / END OF FACTS DEVICE DATA, BEGIN SWITCHED SHUNT DATA
0 / END OF SWITCHED SHUNT DATA, BEGIN GNE DATA
0 / END OF GNE DATA, BEGIN INDUCTION MACHINE DATA
0 / END OF INDUCTION MACHINE DATA


And I attach de dynamic PVD1 model (a distributed PV system model) to the generator in bus 1, using the default parameters. However, when trying to run de transient stability, an error appear in the second 0 saying: 

Number of Viable Islands Changed from 1 to 0
No Viable Islands -- Solution Aborted

The island is: 
Slack Bus Number    Slack Bus Name    Total Buses    Energized    Gen MW      Gen Mvar    Load MW    Load Mvar    Scheduled Exports    DC MW Exports
             1                                       BUS1                2                YES                   106,5    46,0                 106,5                      38,8        0,0                             0,0

I don't get why the island is not viable. I don't know why it doesn't  meet the criteria or what is happening...I have found the criteria are:
      1. At least one island bus has some on-line generation with a positive Maximum MW Limit and is NOT set to regulate the voltage at a bus in another island.
      2. At least one island bus has a closed load (Note: It could still be a 0.0 MW load) OR the island is connected to another island by a DC transmission line.

If anyone could help me I would be so grateful. I am completely stuck.

Thanks,

Maria
 

Hi Maria,

Do you have image or any screenshot regarding to this one? In case you need some notes related to powerworld, try to check on "Power System Analysis and Design" Book of Glover, Overbye, and Sarma., 5th Edition if you have.

I've seen SI Ed. on the net, link -> "SI Ed. Power System Analysis and Design":http://s1.downloadmienphi.net/file/downloadfile6/192/1385298.pdf

Hope it helps.

Best,
Neil