Simulation Circuit and miKroC Code for Automatic Power Factor Correction with PIC16F877A

somebody help me the working simulation circuit for automatic power factor controller together with miKroC CODES i have some codes and circuit upon compilation they give no errors but they arent giving any output when loaded on PIC 16F877A help me please here under are my codes


[code]//LCD Module Connections
sbit LCD_RS at RB4_bit;
sbit LCD_EN at RB5_bit;
sbit LCD_D4 at RB0_bit;
sbit LCD_D5 at RB1_bit;
sbit LCD_D6 at RB2_bit;
sbit LCD_D7 at RB3_bit;
sbit LCD_RS_Direction at TRISB4_bit;
sbit LCD_EN_Direction at TRISB5_bit;
sbit LCD_D4_Direction at TRISB0_bit;
sbit LCD_D5_Direction at TRISB1_bit;
sbit LCD_D6_Direction at TRISB2_bit;
sbit LCD_D7_Direction at TRISB3_bit;
//End LCD Module Connections
int powerFactor()
{
int a=0,b=0,t=0,x=0;
float tm,pf;
TMR1L=0;
TMR1H=0;
do
{
if(PORTA.F0 == 1)
T1CON.F0 = 1;
else if(PORTA.F0 == 0 && T1CON.F0 == 1)
{
T1CON.F0 = 0;
break;
}
}while(1);
a = (TMR1L | (TMR1H

Helps if you put this into code tags

Can you re submit please its so un readable and Im not going to edit all your code to work out what line is where and whats going on so can re do this Im sure no one else will either with that submission

Also could you tell us what its supposed to be doing with some of the maths please as well ?

Like a flow chart perhaps if thats possible

Also a schematic of what your doing
Also an algorythm
Also are you using some type of timer interrupt where is this in the code

What you are trying to achieve perhaps an explanations there as well might be helpfull

It is a bit of a joke really this

Here is some code no out put from where what to what and why No maths explained no nothing a bit like all or some of your exports / imports at the moment isnt it ??

Doesent it look the bizza hey !!

Here buy this but we dont supply any technical information or parts Oh by the way minimu order is 1000 pieces Pieces of what i ask ?

Like this example as well Another one !!
Oh Yes by the way its mosfet you know Got to see this one I don’t think I can stand too much more of these so called fantastic entrepreneurs here or abroad


http://electronic-schema-assembly.blogspot.co...ema-and-production-of-pa-ampli-ibiza.html?m=0

[code]
/LCD Module Connections
sbit LCD_RS at RB4_bit;
sbit LCD_EN at RB5_bit;
sbit LCD_D4 at RB0_bit;
sbit LCD_D5 at RB1_bit;
sbit LCD_D6 at RB2_bit;
sbit LCD_D7 at RB3_bit;
sbit LCD_RS_Direction at TRISB4_bit;
sbit LCD_EN_Direction at TRISB5_bit;
sbit LCD_D4_Direction at TRISB0_bit;
sbit LCD_D5_Direction at TRISB1_bit;
sbit LCD_D6_Direction at TRISB2_bit;
sbit LCD_D7_Direction at TRISB3_bit;
//End LCD Module Connections
int powerFactor()
{ int a=0,b=0,t=0,x=0; float tm,pf; TMR1L=0; TMR1H=0; do { if(PORTA.F0 1) T1CON.F0 = 1; else if(PORTA.F0 0 && T1CON.F0 1) { T1CON.F0 = 0; break; } }while(1); a = (TMR1L | (TMR1H

Not that this has anything to do with the code displayed and the questions asked but of course one can tell that the quality has a rather similar transparency and air about the subject

Yes its not good news at all is it anymore These standards are appauling every single bussiness big and small and lots of increases and no jobs

I dont think this is clever at all i hope they have some explanations to all of this !! hmmmm We see soon

There you go be on the look out for these by the way no service data aexcept what Ive found no real service sheets ,very poor design, very cheap

Also useless and no address for the manufacturer either