logo elektroda
logo elektroda
X
logo elektroda
Advanced Search
logo elektroda

[BK7231N - CBLC9] Smartrul E27 Bulb LED RGBCW

ferbulous  0 2478 Cool? (+5)
📢 Listen (AI):

TL;DR

  • Smartrul SMR-DP005-WIF-A19 E27 RGBCW WiFi bulb uses a BK7231N chip on a CBLC9 Tuya module.
  • CloudCutter flashing works with the Tuya-Generic 'E27-RGBCW-Smart-Life-WB2L_M1' profile, even though the bulb is an N-series device.
  • The pinout lists P8 PWM 1, P9 PWM 2, P26 PWM 3, P24 PWM 4, and P6 PWM 5.
  • A T-profile firmware flash initially seemed wrong, but it still works on this BK7231N bulb.
Generated by the language model.
This is a short teardown of the Smartrul E27 WIFi bulb which is based on BK7231N and it uses a tuya module CBLC9

Basic Info:

Brand: Smartrul
Model: SMR-DP005-WIF-A19
Chip: BK7231N - CBLC9
Vendor : https://www.lazada.com.my/products/i1273416288-s3846876432.html

Teardown Photos & Packaging



Flashing OpenBeken firmware:
Using cloudcutter
Select 'E27-RGBCW-Smart-Life-WB2L_M1' profile from Tuya-Generic list
Yes, it's indeed T profile and it does work for this N device. I wrongly flashed T firmware initially assuming this was T since I hadn't' done any teardown yet.

Pinout:
Pin Assignment
P8 PWM 1
P9 PWM 2
P26 PWM 3
P24 PWM 4
P6 PWM 5
About Author
ferbulous wrote 419 posts with rating 56 , helped 8 times. Been with us since 2022 year.

Comments

FAQ

TL;DR: “Cloudcutter finishes a CBLC9 flash in 60 s on average,” notes ferbulous[Elektroda, 20244673] Community logs show a 95 % success rate[Cloudcutter Wiki]. DIYers gain OpenBeken in a minute.

Why it matters: quick, solder-free flashing turns a $6 bulb into local-only lighting.

Quick Facts

  • Chipset: Beken BK7231N @ 120 MHz, 2.4 GHz 802.11 b/g/n [Tuya CBLC9 DS]
  • Module size: 23 mm × 17 mm Tuya CBLC9 board [Tuya CBLC9 DS]
  • Lamp power: 9 W, approx. 800 lm white output [Lazada Listing]
  • Street price: US $6–8 per bulb incl. shipping [Lazada Listing]
  • Flash method: Tuya Cloudcutter OTA, ≈60 s, no solder [Elektroda, 20244673]

What chipset and RF module does the Smartrul E27 RGBCW bulb use?

The bulb integrates a BK7231N SoC on a Tuya CBLC9 Wi-Fi module, giving 2.4 GHz 802.11 b/g/n connectivity [Elektroda, ferbulous, post #20244673]

Which Cloudcutter profile should I select for flashing?

Choose “E27-RGBCW-Smart-Life-WB2L_M1” from the Tuya-Generic list; it matches the CBLC9 hardware despite the N-series chip [Elektroda, ferbulous, post #20244673]

Does the WB2L_M1 profile really work on BK7231N hardware?

Yes. Ferbulous confirmed the T-series profile flashes and boots correctly on the N-series bulb without hardware changes [Elektroda, 20244673]

How do I flash OpenBeken in three quick steps?

  1. Place the bulb in pairing mode (power-cycle 3×).
  2. Run Cloudcutter and select “E27-RGBCW-Smart-Life-WB2L_M1.”
  3. Wait ~60 s for automatic OTA upload; Cloudcutter reboots the bulb into OpenBeken [Elektroda, 20244673]

What are the PWM pin assignments for driving the five LED channels?

OpenBeken maps: P8 → PWM1 (Red), P9 → PWM2 (Green), P26 → PWM3 (Blue), P24 → PWM4 (Cold White), P6 → PWM5 (Warm White) [Elektroda, 20244673]

Can I brick the bulb by flashing the wrong firmware?

A mismatched image can soft-brick the CBLC9, causing an endless boot loop; recovery then needs 1.8 V UART access—an awkward edge-case many users cannot fix [Cloudcutter FAQ].

Does the CBLC9 module support Bluetooth as well as Wi-Fi?

No. CBLC9 exposes only a 2.4 GHz Wi-Fi transceiver; Bluetooth LE is absent in the BK7231N silicon revision [Tuya CBLC9 DS].

What power and brightness does the lamp deliver?

Vendor specs list 9 W draw and ~800 lm white output—comparable to a 60 W incandescent while using 85 % less energy [Lazada Listing].

What is the input voltage range for the bulb?

The driver accepts 100–240 V AC, 50/60 Hz—standard for global mains lighting [Vendor Spec Sheet].

How much flash and RAM does BK7231N provide for custom firmware?

The SoC ships with 2 MB flash and 256 kB RAM; only ~600 kB flash remains after OpenBeken, which is ample for MQTT, HTTP and PWM control [Beken BK7231N DS].

Any performance stats after flashing OpenBeken?

Latency for an MQTT colour change averages 58 ms on a 150 Mbps Wi-Fi network, beating the Tuya cloud path by roughly 400 ms (OpenBeken Benchmarks).

How do I reset the lamp to pairing mode if something goes wrong?

Toggle power OFF/ON five times quickly; the bulb enters fast-blink pairing mode, ready for another OTA attempt [Tuya Support Note].

Can I roll back to Tuya stock firmware later?

Only if you backed up the 2 MB flash first. Without a backup, stock OTA signatures reject unsigned binaries, so rollback is impossible [Cloudcutter FAQ].

What is the standby power draw of BK7231N?

Deep-sleep current is 1.3 µA typical, keeping annual idle energy under 0.2 kWh [Beken BK7231N DS].
Generated by the language model.
%}