FAQ
TL;DR: A 2048-code RC5 matrix means only 2 k signals cover most TVs, and “IR rays are invisible to the human eye” [Elektroda, RADKON, post #3303710] Build an IR "sniper" with a universal remote, photodiode, and binocular-mounted IR LED to silence noisy gear up to ~30 m away. Why it matters: This FAQ helps apartment dwellers quietly disable or control neighbours’ loud TVs or stereos without confrontation.
Quick Facts
• Typical IR LED wavelength: 940 nm ± 20 nm [Osram Data, 2023]
• RC5 protocol: 32 device addresses × 64 commands = 2048 codes [Elektroda, Marcin1326, post #3307267]
• DIY range with 1 W IR LED & optics: 20–40 m line-of-sight [Elektroda, kiler129, post #3302821]
• Salvageable IR laser diode: found in CD-RW drives, output ≈ 30 mW [Elektroda, kiler129, post #3303773]
• Entry-level universal remote price: PLN 15 (~€3) [Elektroda, arek14, post #3319959]
How far can a binocular-mounted IR “TV sniper” really reach?
Users report 20–40 m when combining a narrow-beam IR LED or salvaged 30 mW laser with 8×–10× binocular optics [Elektroda, kiler129, post #3302821] A clean window can cut range by about 30 % due to glass attenuation [IEC 60825-1]. Line-of-sight is essential.
Will the signal go through walls or bounce off surfaces?
IR photons do not penetrate walls; they reflect weakly. A matte painted wall reflects < 10 % of IR energy, usually insufficient to trigger a TV sensor [Elektroda, RADKON, post #3303695] Mirrors or bright gloss paint can provide workable reflection angles under 15°.
What parts can I recycle for the IR laser or LED?
CD-RW and DVD-RW drives contain 780–820 nm IR laser diodes rated around 30 mW CW; desolder with ESD safety [Elektroda, kiler129, post #3303773] Keep the drive lens assembly for easy collimation. Old set-top boxes donate TSOP1738 photodiodes for the receiver.
Why is there a photodiode in the posted schematic?
The photodiode acts as the front-end receiver. It captures your handheld remote’s signal, letting the amplifier and high-power LED relay the exact code without microcontrollers [Elektroda, A_Romek, post #3303699] This preserves full protocol compatibility.
How can I amplify my universal remote for longer range?
1 Attach the remote’s IR LED output to the schematic’s NPN-driven power stage.
2 Use 4 × AA NiMH cells (≈5 V) to supply up to 200 mA peak.
3 Mount the LED at the binocular focus.
This triples peak radiant power while keeping timing intact [Elektroda, mariusz p, #3312576].
How many RC5 codes would a brute-force jammer need to send?
The RC5 standard uses 2048 unique words (32 addresses × 64 commands) [Elektroda, Marcin1326, post #3307267] At 14 bits per code and 114 ms per frame, brute-forcing the entire set takes ≈ 234 s—fast enough for prank use but still noticeable.
Can I adapt the circuit to mute or switch off a neighbour’s hi-fi tower?
Yes, if the stereo accepts IR control. Program a universal remote with the tower’s brand code, then feed it through the same IR amplifier. If the tower lacks IR, this method fails—consider power-line filters or direct discussion [Elektroda, Jarema, post #3304832]
Is it legal to disable someone else’s equipment remotely?
In most EU jurisdictions, intentionally interfering with another person’s electronics breaches Article 269 of penal codes and can incur fines or jail. Use only on your own devices or with permission [EUR-Lex 2013].
Could an IR laser from a CD-RW blind me?
Yes. Class 3B diodes exceed 5 mW. Exposure above 10 mW at close range risks retinal burns in under 0.25 s—even though the beam is invisible [FDA Laser Safety, 2022]. Always use IR-rated goggles during alignment.
What’s an edge case where the setup fails?
Tinted low-E windows block up to 90 % of 940 nm IR. If your neighbour has such glazing, the amplified signal may drop below the 0.6 V detection threshold of TV sensors, rendering the attack ineffective [Pilkington Glass Spec, 2021].
How do I build a simple room-to-room IR extender instead?
- Place the photodiode module near your living-room TV.
- Run shielded cable to an IR LED in the bedroom.
- Drive it with the two-transistor buffer from the forum schematic.
Now one remote works in both rooms [Elektroda, michal.rogaczewski, post #3315741]
Why did the original design use two transistors instead of one?
The first NPN provides high input impedance for the photodiode; the second supplies up to 200 mA pulse current to the LED. Splitting tasks avoids waveform distortion and protects the photodiode from reverse bias [Elektroda, koloj, post #3308504]
Can an LM386 audio amp replace the transistor driver?
No. The LM386’s bandwidth peaks at audio (≤ 300 kHz), and its slew-rate limits the 36–40 kHz IR carrier, causing rounded edges that most TV decoders reject [Elektroda, biscent12, post #3308808]
What’s the cost to build the full rig?
• Universal remote: PLN 15
• Budget binoculars: PLN 25
• IR LED & transistors: PLN 8
• Misc. PCB & battery: PLN 12
Total ≈ PLN 60 (~€13) [Elektroda, arek14, post #3319959]
Any quick expert tip for first-time builders?
“Start with a breadboard indoors; confirm the photodiode correctly retransmits before adding optics.” — senior user MacGyver. [Elektroda, MacGyver., post #3303014]
Comments
Good idea All you need is a programmable remote control and some "spy" giving the neighbor's TV model ;) [Read more]
Not necessarily:] Look at the rtv fool schematic from my bridge above :D edit: Thanks to gulson - points are always useful, I will try to help with translations, although it is formally from this Shqippy,... [Read more]
Cool thing :) )) I wonder if the "light" from IRka has been thrown on the wall, or if the TV will turn off ... because sometimes the neighborhood has a TV set in such a way that it will not aim directly... [Read more]
Well, in my housing estate, most of the people have a TV set with its back to the window, but what some have in front of it :wink: so one could experiment a bit with that :cunning: I think he will assemble... [Read more]
And when it comes to mirror coverings, I don't know, but if I have strong batteries in the remote control, I can do it in such a way that I bounce off the wall because if it's weak, there's... [Read more]
Well, you are right, because IR rays are not the same as radio waves, so they do not penetrate the wall, and they probably bounce off it. :) I wonder at what angle you need to set the binoculars to reflect... [Read more]
This is not an ordinary laser pointer or any other toy, but an infrared laser module. You can buy it from the Russians, but rather only with night vision devices, you can also look for it in medical equipment.... [Read more]
Laser ir? No problem ! Old cd / rw is enough. I think they were like that in cd readers, for sure in cd recorders, they were laser diodes but operating in infrared :D [Read more]
It's a pity that I live in a detached house and can't try this layout out. [Read more]
And it would be possible to do something like this only for the tower? ;] I have a problem with a neighbor who loves loud music after 23;] [Read more]
Object cool. Since the universal remote control, you can control the tower. And my dear, if you have a problem with a neighbor, you'd better go to her after 23, maybe she dances in the right outfit.... [Read more]
and I have one question looking at the documentation for the device described by my colleague kiler129 - does my friend know Polish? :?: [Read more]
Hello, Provided that the tower is controlled by a remote control. A brilliant idea would be to control, for example, a tower that does not have a remote control and I do not mean twisting the fuses... [Read more]
And if so, I will probably try to do this project;] Personally, I do not see any reason for me to flinch;] You don't live badly with a neighbor, her only problem is that she forgets that some people... [Read more]
um, gentlemen, the best and very effective solution is to use targeted EPM (electromagnetic pulse) - one shot and the equipment. Of course you have to deal with the generator power supply, but what for... [Read more]
or maybe a magnetron from a microwave oven? :) if the wall is not thick, it is effective [Read more]
Great layout but for my neighbors because I like to make noise :) [Read more]
And it does not work sometimes that you need a special TV-B-Gone remote control and this system only receives the data from the remote control via a photo diode and sends it through a more powerful ir... [Read more]
I guess EMP (ElectroMagnetic Pulse) or something like that :D [Read more]