Woox R6132 Smart WiFi Multi Power Socket Configuration and Internal Overview
Hi All,
Today, I received my two Woox R6132 SMART WIFI MULTI POWER SOCKETS.
They were reasonably priced, and buying two saved me on shipping costs.
The device consists of 4 relays. Three of them control the power sockets, and one controls the power to the USB ports for charging your favorite devices.
Total charging power is 3A@5Volt. The device comes with 2 USB-C ports and 2 Classic USB ports.
Some pictures to start with:
Well, usually, I am okay with just configuring the device, preferably without cracking the case. However, Once I finished configuring the relays, I noticed it should come with a power meter. And that means looking for the chip that does the monitoring thing.
In this case, the screw heads were flattened, and there was no way for me to open the casing. So, I sacrificed one unit.
bottom plate ;(
After opening the unit, the inside looks like this.
Main circuit
So, the technical details:
The unit comes with a WB3S (https://developer.tuya.com/en/docs/iot/wb3s-module-datasheet?id=K9dx20n6hz5n4) labeled board soldered on the main circuit board. Our trustful BK7231T module is doing its job.
The WB3S controls the four relays, the power meter circuit (BL0937), and mine ran Tuya v1.3.5.
Getting it into recovery mode is straightforward. Power it on. Push the button until the led starts blinking slowly. Release the bottom and press it again until it goes off. Bang. You're in recovery mode.
Run cloudcutter and flash it with BK7231t 1.3.5 firmware cutter and flash it the flavor of your choice.
Here is the template:
Once you have applied it, please remember to calibrate the power using a 60-watt light bulb and a multimeter.
PowerSet 60 (for the wattage of the bulb)
VoltageSet 231 (set your voltage from the multimeter)
CurretSet 0.261 (calculated 1000*(60/231)
Configure HomeAssistant, and it will nicely show up
I played around with it, and it works like a charm.
I hope you enjoyed it, and if you have a device you want me to purchase and investigate, happy to do so!
Cheers
Today, I received my two Woox R6132 SMART WIFI MULTI POWER SOCKETS.
They were reasonably priced, and buying two saved me on shipping costs.
The device consists of 4 relays. Three of them control the power sockets, and one controls the power to the USB ports for charging your favorite devices.
Total charging power is 3A@5Volt. The device comes with 2 USB-C ports and 2 Classic USB ports.
Some pictures to start with:
Well, usually, I am okay with just configuring the device, preferably without cracking the case. However, Once I finished configuring the relays, I noticed it should come with a power meter. And that means looking for the chip that does the monitoring thing.
In this case, the screw heads were flattened, and there was no way for me to open the casing. So, I sacrificed one unit.
bottom plate ;(
After opening the unit, the inside looks like this.
Main circuit
So, the technical details:
The unit comes with a WB3S (https://developer.tuya.com/en/docs/iot/wb3s-module-datasheet?id=K9dx20n6hz5n4) labeled board soldered on the main circuit board. Our trustful BK7231T module is doing its job.
The WB3S controls the four relays, the power meter circuit (BL0937), and mine ran Tuya v1.3.5.
Getting it into recovery mode is straightforward. Power it on. Push the button until the led starts blinking slowly. Release the bottom and press it again until it goes off. Bang. You're in recovery mode.
Run cloudcutter and flash it with BK7231t 1.3.5 firmware cutter and flash it the flavor of your choice.
Here is the template:
Code: JSON
Once you have applied it, please remember to calibrate the power using a 60-watt light bulb and a multimeter.
PowerSet 60 (for the wattage of the bulb)
VoltageSet 231 (set your voltage from the multimeter)
CurretSet 0.261 (calculated 1000*(60/231)
Configure HomeAssistant, and it will nicely show up
I played around with it, and it works like a charm.
I hope you enjoyed it, and if you have a device you want me to purchase and investigate, happy to do so!
Cheers
Comments
I flashed a Woox power strip once, but it was easier to open. Futhermore, it had ESP8266 inside: https://www.elektroda.com/rtvforum/viewtopic.php?p=20964495#20964495 https://www.elektroda.pl/rtvforum/viewtopic.php?p=20964495#20964495 I... [Read more]
Hi, I don't have any devices for sale :). But I like purchasing Smart devices, hoping they contain BK chips, and adding them to my HomeAssistant. So, every two months, I spend about 25 euros on a new... [Read more]
That's what I meant, I asked which devices are available for purchase for you. In general, anything that is not yet on our list here: https://openbekeniot.github.io/webapp/devicesList.html should be... [Read more]
Just volunteering :) [Read more]
Would you like to free from the cloud some simple device? Or would you rather try something harder, maybe TuyaMCU based? I can guide you step by step in case of more advanced devices. [Read more]
I have already tinkered with about 20 devices, ranging from simple relays to impulse counters to TuyaMCU electricity meters. I'm looking around for new devices to break down and add to the list. As I don't... [Read more]
I am also doing lots of teardowns, here you can see my latest ones: https://www.elektroda.com/rtvforum/topic4049884.html https://www.elektroda.com/rtvforum/topic4048894.html https://www.elektroda.com/rtvforum/topic4047343.html https://www.elektroda.com/rtvforum/topic4046607.html I... [Read more]
Check. Keep you posted [Read more]
added https://github.com/OpenBekenIOT/webapp/pull/105/commits/1c0600533a804a82e964ee006cc64d96afdc85ba [Read more]